Wi-Fi settings guide · Updated November 2026

How Do You Set Up a Guest Network on the Minion Router?

Kevin can broadcast multiple SSIDs per band, which lets you separate guest phones, work devices or lower-trust smart-home equipment from the main network. The exact guest controls, client isolation and subnetwork behavior depend on the firmware, so this guide separates what is confirmed from what you must verify in the admin interface.

SSIDs per bandUp to 7Main controlsBrowser adminSecurityWPA3IsolationVerify firmware
A Wi-Fi 6E router with separate main, guest and smart-home network paths on a phone and laptop

Does the Minion Router support a guest network?

RTINGS documents support for up to seven unique SSIDs per band on the Minions Kevin, explicitly noting that the feature can isolate lower-security IoT devices from the main network or create a subnetwork with parental controls. That confirms multiple wireless networks; it does not confirm that every firmware revision offers the same dedicated “Guest Network” toggle or full client isolation.

  • Confirmed: multiple SSIDs per 2.4, 5 and 6 GHz band
  • Confirmed: browser-based network management
  • Confirmed: WPA3 security support
  • Verify locally: dedicated Guest mode, guest portal and client isolation
  • Verify locally: separate DHCP subnet or VLAN controls

Open the Kevin admin interface and look for Guest Network, Additional SSID, Wireless Network or VLAN before following a generic router tutorial.

What is the difference between an SSID and a guest network?

An SSID is the Wi-Fi network name a device sees. Multiple SSIDs can carry different passwords, security settings or policies, but they are not automatically isolated from one another. A true guest network normally adds restrictions such as blocking access to the main LAN, preventing guest-to-guest communication or providing a separate subnet.

FeatureExtra SSIDTrue guest network
Separate name and passwordYesYes
Main-network client isolationNot guaranteedUsually, when the firmware implements it
Separate DHCP subnetFirmware-dependentCommon
Captive portal or guest splash pageNot impliedSome systems provide it
Good for simple device separationOftenYes, when correctly configured

The safest interpretation is literal: a second SSID is a second Wi-Fi network name. Treat it as a security boundary only after testing whether a connected device can still reach the main router's administration page or other private clients.

How do you create a separate SSID on Kevin?

  1. 1. Open the router interface

    Connect to Kevin and open the local admin page or app. The admin login guide covers the label address and administrator login.

  2. 2. Choose the intended band

    Open the 2.4, 5 or 6 GHz wireless settings. Bands can have different client compatibility and coverage, so choose the radio the guest devices actually support.

  3. 3. Add a new SSID

    Look for Add SSID, Additional Network, Guest Network or a similar control. Record the current main SSID before changing anything.

  4. 4. Use a unique WPA3 password

    Give the network a recognizable name and its own password. Use WPA2/WPA3 mixed mode only when an older guest device cannot connect with WPA3.

  5. 5. Apply only confirmed restrictions

    If the page offers guest isolation, access schedules or bandwidth limits, enable the intended policy. Do not assume those controls exist when they are absent.

  6. 6. Test before sharing access

    Join from a phone, confirm internet access and then check whether that phone can reach the router admin page or another private device.

Should the guest network use 2.4, 5 or 6 GHz?

Use 5 GHz for most phones, tablets and streaming guests because it balances speed and range. Use 2.4 GHz for older devices and longer distance. Use 6 GHz only for visitors with Wi-Fi 6E hardware and only when they will stay relatively close to the router.

  • 2.4 GHz: broad compatibility, slower speed and more interference
  • 5 GHz: best default for guest phones and laptops
  • 6 GHz: cleaner spectrum but shorter reach and Wi-Fi 6E client requirement
  • Same SSID name across bands: simpler discovery when the firmware coordinates it well
  • Separate names: easier troubleshooting but less seamless roaming

For the main network, use the range guide to choose band placement. Guest access should not be stretched into a weak far room using a repeater unless isolation remains intact.

Should smart-home and IoT devices use the guest network?

Separating inexpensive or rarely updated smart-home devices from phones and computers reduces accidental cross-device exposure. RTINGS specifically identifies IoT isolation as a practical use for Kevin's multiple SSIDs. It is not a substitute for patching the devices, but it can limit which clients share the same wireless trust zone.

  • Use 2.4 GHz for smart plugs, bulbs and appliances that do not support 5 GHz
  • Keep cameras and door locks on a network with a unique password
  • Do not share the administrator password with guests or IoT setup apps
  • Check whether the app needs local discovery and will fail if strict isolation is enabled
  • Keep critical work devices on the main network unless the firmware supports managed segmentation

How do you verify that the guest network is isolated?

  1. 1. Connect the test device to the guest SSID

    Use a device without cellular fallback or disable mobile data so you know traffic is using Kevin.

  2. 2. Confirm internet access

    Load a public website. If the guest network lacks internet, first check the SSID's DHCP and access policy.

  3. 3. Try the router admin address

    A properly isolated guest client should not be able to open Kevin's management page. Use the exact local address from the router label.

  4. 4. Try another private client

    Test a non-sensitive device on the main network. Stop if you are unsure which firewall or operating-system prompt to approve.

  5. 5. Revoke access if isolation fails

    If guests can reach private clients and the firmware has no isolation option, use a separate access point or router with a proper guest VLAN instead of treating the extra SSID as secure.

Do not test isolation by exposing a real NAS, printer or work computer administration page to an untrusted network. Use a temporary non-sensitive device or ask the seller for the exact VLAN and guest-mode behavior.

Why can't devices connect to the new SSID?

  • The device may not support the selected band, especially 6 GHz
  • An older client may reject WPA3-only security; use mixed mode temporarily
  • The SSID may be hidden and not joined manually
  • The guest policy may block DHCP or require a captive-portal step
  • A mesh node may not support a custom SSID on the current firmware
  • The router may require Save, Apply or a reboot after the new SSID is created

Return to the same wireless page and verify the SSID is enabled on the expected band. For broader connection failures, use the Minion router troubleshooting guide.

Key takeaways

  • Kevin supports up to seven SSIDs per band according to RTINGS
  • A second SSID is not automatically an isolated guest network
  • Use a dedicated Guest mode when the firmware provides one
  • Test access to the admin page and private clients before trusting the boundary
  • 5 GHz is the best default for guest phones; 6 GHz is for nearby 6E devices

SSID capability comes from the RTINGS Kevin review. Exact menu names and isolation behavior must be verified in the firmware for your own unit. For the hardware verdict, see the Kevin review; for current kits, check the price page.

Frequently asked questions

Does the Minion Router have a guest network?

Kevin supports multiple SSIDs per band, so you can create a guest-style wireless network. Dedicated Guest mode and full client isolation depend on the exact firmware; verify the admin interface and test access before relying on it.

How many SSIDs can the Minions Kevin create?

RTINGS documents up to seven separate SSIDs per band across 2.4, 5 and 6 GHz. Feasible combinations may be limited by the firmware and regional version.

Is a separate SSID the same as a VLAN?

No. An SSID is only a Wi-Fi network name and policy entry. A VLAN or true guest network provides stronger traffic separation at the router. Do not assume VLAN isolation just because two SSIDs exist.

Which band should I use for a guest network?

Use 5 GHz for most phones and laptops, 2.4 GHz for older or distant devices, and 6 GHz for nearby Wi-Fi 6E visitors. 6 GHz requires a compatible client.

Can I isolate smart-home devices with a second SSID?

A separate SSID can organize IoT devices and give them a unique password, but real isolation requires a guest policy, firewall rule or VLAN. Test whether IoT clients can reach the router admin page or main-network devices.

Why won't my guest device connect to the new SSID?

Check band support first, especially for 6 GHz, then verify WPA3 compatibility, whether the SSID is enabled, DHCP or captive-portal requirements, and whether the current mesh firmware supports custom SSIDs.

Build a cleaner home network

Minions Kevin starts at $102.99 with Wi-Fi 6E, WPA3 and multiple-SSID controls.

Minion Router Guest Network: Separate SSIDs Guide (2026)